|
GTX327 to AXP340 wiring |
Post Reply 
|
| Author | |
dan300 
Newbie 
Joined: 09 Oct 2018 Location: 63367 Status: Offline Points: 10 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: GTX327 to AXP340 wiringPosted: 09 Oct 2018 at 9:57am |
|
Anybody have the pin-for-pin to do this?
This is what I have:   Edited by dan300 - 09 Oct 2018 at 10:03am |
|
 |
|
|
forkauto
Groupie 
Joined: 30 Apr 2018 Location: Maryland Status: Offline Points: 51 |
Post Options
Thanks(0)
Quote Reply
Posted: 09 Oct 2018 at 10:45am |
|
Here you go!
 |
|
|
|
|
dan300
Newbie
Joined: 09 Oct 2018 Location: 63367 Status: Offline Points: 10 |
Post Options
Thanks(0)
Quote Reply
Posted: 09 Oct 2018 at 11:13am |
|
Thanks for the response, but I don't think that is what I'm looking for.
I need to connect a GTX327 harness to a AXP340. |
|
|
|
|
Ibraham
Senior Member 
Joined: 21 May 2016 Location: KHWO Status: Offline Points: 363 |
Post Options
Thanks(0)
Quote Reply
Posted: 10 Oct 2018 at 5:14am |
|
Are you replacing GTX327 with AXP340?
|
|
|
|
|
dan300
Newbie
Joined: 09 Oct 2018 Location: 63367 Status: Offline Points: 10 |
Post Options
Thanks(0)
Quote Reply
Posted: 10 Oct 2018 at 5:39am |
|
Yes
|
|
|
|
|
Ibraham
Senior Member
Joined: 21 May 2016 Location: KHWO Status: Offline Points: 363 |
Post Options
Thanks(0)
Quote Reply
Posted: 10 Oct 2018 at 6:24am |
|
To be ADS-B compliant, the AXP340 needs an approved WAAS GPS navigator to supply GPS position, which is not the case for the GTX327, therefore you may need to replace the harness. Which WAAS GPS do you have? Do you have an experimental aircraft?
|
|
|
|
|
dan300
Newbie
Joined: 09 Oct 2018 Location: 63367 Status: Offline Points: 10 |
Post Options
Thanks(0)
Quote Reply
Posted: 10 Oct 2018 at 4:08pm |
|
Cirrus with two GNS430W.
There's a wire from GPS1 to pin 2 on the GTX327. I think putting it to pin 3 of the secondary connector like shown above takes care of the WAAS in. Existing wiring:  Edited by dan300 - 10 Oct 2018 at 4:09pm |
|
|
|
|
Ibraham
Senior Member
Joined: 21 May 2016 Location: KHWO Status: Offline Points: 363 |
Post Options
Thanks(0)
Quote Reply
Posted: 11 Oct 2018 at 6:58am |
|
This installation requires an avionics shop with an A&P signoff. Unless you have weather and traffic, GTX345 may be a better option (will also display weather and traffic on the MFD with release 8.2 software). FYI, here is the AXP340 basic interconnect diagram.
 |
|
|
|
|
dan300
Newbie
Joined: 09 Oct 2018 Location: 63367 Status: Offline Points: 10 |
Post Options
Thanks(0)
Quote Reply
Posted: 11 Oct 2018 at 7:17am |
|
Yes, I'm just doing some legwork for my avionics guy. He hasn't done a 340 yet. I have weather and traffic and a used 340.
Edited by dan300 - 11 Oct 2018 at 7:18am |
|
|
|
|
Ibraham
Senior Member
Joined: 21 May 2016 Location: KHWO Status: Offline Points: 363 |
Post Options
Thanks(0)
Quote Reply
Posted: 11 Oct 2018 at 1:14pm |
|
You should call Avidyne tech support, they are very helpful and will provide the avionics tech all the documentation and help needed to get it done.
|
|
|
|
|
Post Reply
|
|
| Tweet |
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You can vote in polls in this forum |
Topic Options