|
NO ADS-B OUT |
Post Reply 
|
| Author | |
baldcaldwell 
Newbie 
Joined: 21 Mar 2021 Location: 14A Status: Offline Points: 14 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: NO ADS-B OUTPosted: 30 Apr 2021 at 11:17am |
|
The equipment:
Avidyne IFD-540 SV-XPNDR-261 SV-ADSB-472 SV-HDX-1100/B SV-GPS-250A Well... I tried to post pictures but this forum will not accepts files larger than 1MB.... So I'm not sure how you guys can help me without some visuals... SV-HDX-1100B message says "NO ADS-B OUT: GPS LOST" We need the GPS signal from the IFD-540 WAAS Navigator. We have confirmed the GPS signal for the IFD-540 is working in all other aspects. A multimeter confirms the GPS signal from the IFD-540 is pulsing at Pin 3 on the cable into the SV-XPNDR-261. The 2nd picture here shows NO GPS DATA in the HDX under transponder settings. The 3rd picture here shows NO ADSB POS in the HDX under transponder settings. 1.21k Ohm Resistor at the #3 pin on SV-XPNDR-261. At this point, we are stuck. If I switch over to SV-GPS-250A, ADS-B OUT works. But we cannot use the SV-GPS-250A for ADS-B OUT. Any thoughts? We are at a loss... Thanks! |
|
|
Rob Caldwell
Lake Norman Airpark (14A), North Carolina EAA Chapter 309 Model B Quick Build Kit Serial # 11B-24B / 25B YouTube Channel: http://bearhawklife.video 1st Flight May 18, 2021 |
|
 |
|
|
eallevato
Groupie 
Joined: 04 Apr 2018 Location: Northridge, CA Status: Offline Points: 69 |
Post Options
Thanks(0)
Quote Reply
Posted: 30 Apr 2021 at 10:07pm |
|
What serial output format did you configure the serial port on the 440?
Gene
|
|
|
Gene
|
|
|
|
|
baldcaldwell
Newbie
Joined: 21 Mar 2021 Location: 14A Status: Offline Points: 14 |
Post Options
Thanks(0)
Quote Reply
Posted: 30 Apr 2021 at 10:19pm |
|
I had the panel built for me. I did not configure it myself. It's a IFD-540.
However, through another forum I was advised to check the connection from pin 58 of the Avidyne 5001 connector to pin 3 to the SV-XPNDR-261. I was not able to confirm continuity. So I bypassed the wire with a new wire and now the ADS-B OUT function works. But... now I am receiving a new error message on the IFD as shown in the attached picture. Oh yeah... can't post pictures.... Error message says "No 429 from input: #1" |
|
|
Rob Caldwell
Lake Norman Airpark (14A), North Carolina EAA Chapter 309 Model B Quick Build Kit Serial # 11B-24B / 25B YouTube Channel: http://bearhawklife.video 1st Flight May 18, 2021 |
|
|
|
|
eallevato
Groupie
Joined: 04 Apr 2018 Location: Northridge, CA Status: Offline Points: 69 |
Post Options
Thanks(0)
Quote Reply
Posted: 01 May 2021 at 12:48am |
|
OK, so what is connected to ARINC 429 IN 1? Could be a LOW vs HIGH Speed selection, or the wrong protocol selected. Did they give you a schematic for your panel? Gen
|
|
|
Gene
|
|
|
|
|
baldcaldwell
Newbie
Joined: 21 Mar 2021 Location: 14A Status: Offline Points: 14 |
Post Options
Thanks(0)
Quote Reply
Posted: 01 May 2021 at 1:24pm |
|
Here's the ARINC settings. BTW... I fixed the ADS-B OUT problem. Replaced the wire from Pin 58 of the 5001 connector to Pin 3 on the SV-XPNDR-261 (with 1.21 K Ohm resistor). NOW... I am getting the following ARINC ALERT (No I do not have a panel schematic. Will request one)   Edited by baldcaldwell - 01 May 2021 at 1:26pm |
|
|
Rob Caldwell
Lake Norman Airpark (14A), North Carolina EAA Chapter 309 Model B Quick Build Kit Serial # 11B-24B / 25B YouTube Channel: http://bearhawklife.video 1st Flight May 18, 2021 |
|
|
|
|
eallevato
Groupie
Joined: 04 Apr 2018 Location: Northridge, CA Status: Offline Points: 69 |
Post Options
Thanks(0)
Quote Reply
Posted: 01 May 2021 at 2:57pm |
|
What EFIS do you have?
Gene
|
|
|
Gene
|
|
|
|
|
eallevato
Groupie
Joined: 04 Apr 2018 Location: Northridge, CA Status: Offline Points: 69 |
Post Options
Thanks(0)
Quote Reply
Posted: 01 May 2021 at 2:58pm |
|
Never mind, you have the Dynon HDX.
Gene
|
|
|
Gene
|
|
|
|
|
eallevato
Groupie
Joined: 04 Apr 2018 Location: Northridge, CA Status: Offline Points: 69 |
Post Options
Thanks(0)
Quote Reply
Posted: 01 May 2021 at 3:15pm |
|
Try In1 Low Airdata Gene
|
|
|
Gene
|
|
|
|
|
baldcaldwell
Newbie
Joined: 21 Mar 2021 Location: 14A Status: Offline Points: 14 |
Post Options
Thanks(0)
Quote Reply
Posted: 01 May 2021 at 6:03pm |
|
Got it fixed. Seems I bent a pin when I reinstalled the IFD. Straightened now and working. Thanks for your help!
|
|
|
Rob Caldwell
Lake Norman Airpark (14A), North Carolina EAA Chapter 309 Model B Quick Build Kit Serial # 11B-24B / 25B YouTube Channel: http://bearhawklife.video 1st Flight May 18, 2021 |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options