Avidyne Homepage
Forum Home Forum Home > Avidyne General > IFD 5 Series & IFD 4 Series Touch Screen GPS/NAV/COM
  New Posts New Posts RSS Feed - 10.2.4.1 question
  FAQ FAQ  Forum Search   Register Register  Login Login

10.2.4.1 question

 Post Reply Post Reply
Author
Message
ddgates View Drop Down
Senior Member
Senior Member
Avatar

Joined: 12 Aug 2011
Location: Deer Valley
Status: Offline
Points: 1100
Post Options Post Options   Thanks (0) Thanks(0)   Quote ddgates Quote  Post ReplyReply Direct Link To This Post Topic: 10.2.4.1 question
    Posted: 27 Apr 2020 at 10:02am
There doesn't seem to be a PG specific to 10.2.4.1?  Perhaps I missed it.

I'd like more info on:
1.  Turning off WiFi ADSB
2.  Maintenance password

Is there material out there on those topics?

Thanks!
David Gates
Back to Top
chflyer View Drop Down
Senior Member
Senior Member
Avatar

Joined: 24 Jan 2013
Location: LSZK
Status: Offline
Points: 1034
Post Options Post Options   Thanks (0) Thanks(0)   Quote chflyer Quote  Post ReplyReply Direct Link To This Post Posted: 28 Apr 2020 at 6:01am
+1
Vince
Back to Top
AviSteve View Drop Down
Admin Group
Admin Group
Avatar

Joined: 12 Feb 2018
Location: Melbourne, FL
Status: Offline
Points: 2244
Post Options Post Options   Thanks (0) Thanks(0)   Quote AviSteve Quote  Post ReplyReply Direct Link To This Post Posted: 28 Apr 2020 at 9:25am
There is no pilot guide update specifically for 10.2.4.1.

WiFi ADS-B
Assuming you are referring to the item on the Setup Page with the title "ADS-B Forwarding".  That item is available when the IFD is configured with an ADS-B in device.  When the selection is "On", the IFD will send ADS-B In data over WiFi for use by applications such as Foreflight.

Maintenance Mode Password Protection PIN
Maintenance mode now has the capability to protect settings by requiring a personal identification number (PIN) to be entered before any settings changes will be accepted.  When no PIN has been defined, settings can be changed without protection of a PIN.

To define a PIN, navigation to the Password Protection PIN page, then press the right knob button.  Use the inner and outer knobs to change characters and move the cursor, respectively.  Once the desired PIN has been entered, press the right knob to set it.  Once the PIN has been set, entry of that PIN will be required to save changes to settings.

Note that the IFD will allow settings to be viewed and changed even without entering the current PIN.  However, any changes will not be saved unless the PIN has been entered.  If the PIN has not been entered, the text "Password - Protected" will be shown in yellow under the page title on any of the pages where settings can normally be changed.



Edited by AviSteve - 28 Apr 2020 at 9:26am
Steve Lindsley
Avidyne Engineering
Back to Top
skybum02 View Drop Down
Groupie
Groupie


Joined: 11 Dec 2017
Status: Offline
Points: 42
Post Options Post Options   Thanks (0) Thanks(0)   Quote skybum02 Quote  Post ReplyReply Direct Link To This Post Posted: 30 Apr 2020 at 3:45pm
Originally posted by AviSteve AviSteve wrote:

There is no pilot guide update specifically for 10.2.4.1.

WiFi ADS-B
Assuming you are referring to the item on the Setup Page with the title "ADS-B Forwarding".  That item is available when the IFD is configured with an ADS-B in device.  When the selection is "On", the IFD will send ADS-B In data over WiFi for use by applications such as Foreflight.

Maintenance Mode Password Protection PIN
Maintenance mode now has the capability to protect settings by requiring a personal identification number (PIN) to be entered before any settings changes will be accepted.  When no PIN has been defined, settings can be changed without protection of a PIN.

To define a PIN, navigation to the Password Protection PIN page, then press the right knob button.  Use the inner and outer knobs to change characters and move the cursor, respectively.  Once the desired PIN has been entered, press the right knob to set it.  Once the PIN has been set, entry of that PIN will be required to save changes to settings.

Note that the IFD will allow settings to be viewed and changed even without entering the current PIN.  However, any changes will not be saved unless the PIN has been entered.  If the PIN has not been entered, the text "Password - Protected" will be shown in yellow under the page title on any of the pages where settings can normally be changed.


Steve, I had a problem with the network settings did not save even-though I think changes to the network settings does not require a PIN.  I had to get the PIN eradication DSF to reset.  It's fixed now.

 Maybe a glitch in the software. 

Cheers, Steve
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.01
Copyright ©2001-2018 Web Wiz Ltd.

This page was generated in 0.148 seconds.